Nabu PC Floppy Disk Controller Reproduction

Several people have asked me about reproducing the Nabu PC Floppy disk controller board even though, at this point, I do NOT have the only original I know of yet working.  If you happen to have a Nabu PC with a working floppy disk drive, please let me know.  I could use some assistance.

The Floppy Disk Controller board allows the Nabu to utilize an external dual floppy disk drive and boot up CP/M 3.  There are disk images with the software on them and I can view the software with other means but at this point, it just does not boot up.  If it could boot a local version of CP/M 3, the Nabu PC would be a stand-alone Nabu PC and you could run CP/M based software on it, as long as it supports 40 columns.

To create a reproduction, you need decent pictures.  Below are the pictures.

Below are pictures of the Nabu Floppy Disk controller card. It is made up of two cards connected together via ribbon cable.  The “FDC Option interface” board connects to ALL four option slots in the Nabu PC.  It also needs to have an 8K Version 2 of the EPROM to work.  Both 4K (non-floppy) and 8K Floppy versions of the EPROM are posted.  NOTE: You have to modify your Nabu motherboard to accept 8K EPROMs if yours came with a 4K EPROM and that is almost all of them.

Here are pictures of the two boards that make up the Nabu PC Floppy Disk controller.  Note once again that the small Option interface board connects to all four of the Options slots as pictured here:

 

 

 

 

 

 

 

The populated front and rear of both boards:

The main Floppy Disk Controller (FDC main) board:

FDC Main front

FDC main rear

 

The Floppy Disk Controller Option interface (FDC  option) board:

FDC option interface front

FDC option interface rear

Since I removed and socketed the chips for troubleshooting purposes, here are pictures underneath most chips:

FDC Main board

FDC main front left side

FDC main front middle section

FDC main front right side

FDC main rear left side

FDC main rear middle section

FDC main rear right side

The FDC Option board has some traces obscured by the ribbon cable.  Here is a better picture with the ribbon removed:

FDC Option board ribbon removed

 

To enable the 8K EPROM, you will need to cut a trace on the motherboard located just to the top right of the Z80 CPU and you will have to solder a jumper to the 8K solder point as shown below.  This will allow you to use the 8K Floppy V2 EPROM.

4K / 8K EPROM jumper location

 

 

 

 

 

 

 

A discussion thread for this project is located at the Vintage Computer Federation Forum here: https://forum.vcfed.org/index.php?threads/the-official-nabu-pc-floppy-disk-controller-thread.1241006/

If you decide to tackle a reproduction of this board, please post in the VCFed thread.  Please create a user ID, if you need to.  This will allow you to see if others are also doing this. Please check there for any updates.  If you have any questions about the Nabu PC floppy disk controller, please post in the thread as others will have similar questions and I may have answered them already there.

Good luck and let me know if you were successful!

3 Responses

  1. Darren Hughes says:

    Wow! Thank you for posting these great pictures! Thank you for removing the chips and retaking the pictures! There will be, if there isn’t already many people who will be so happy that you’ve done all this work!

  2. Jeffrey Worley says:

    Are the gerbers available for this board? I’d love to make a couple.
    Are the board available for purchase? I’d love two.

Leave a Reply to admin Cancel reply

Your email address will not be published. Required fields are marked *